|
Santoemma RESTROOM Cleaning and Sanitizing Program
Cleaning and sanitizing of public
restrooms are important challenges worldwide, which has not found yet an
optimal solution. Cleaning means removing the visible dirt
from all surfaces, while sanitizing means removing not
only visible dirt, but also invisible elements like bacteria, which can be
responsible for disease transmission. This means that even after cleaning,
a truly clean washroom should be periodically sanitized.
Santoemma RESTROOM Cleaning and
Sanitizing Program provides innovative and patented systems for cleaning
and sanitizing public restrooms of any type and size. By using
specially designed machines, instead of manual work only, restrooms are
completely cleaned and sanitized in a short time, with excellent and
granted results. It is finally possible to reach a higher level in
restroom's hygiene, increase productivity and have a higher fulfilment of
the cleaning operators.
Specific systems and machines have
been developed by Santoemma, in order to better
suit any area, according to the type and dimensions of the restrooms to be
cleaned and to their optimal cleaning and sanitizing plan.
Our machines can be used for both
periodic and frequent interventions, even daily.
With the Santoemma RESTROOM program it
is possible to achieve:
· Complete dirt
removal
· Complete sanitizing
· Specific solutions
for any area and cleaning schedule
· Customers'
satisfaction
· Operators' higher fulfilment
· Increased
productivity
· Overall cost
reduction
Santoemma developed
different models, which allow to provide a
"tailor made" solution for any place.
The cleaning and sanitizing process is carried out through four
stages:
1.
Foam spraying on all the surfaces (walls, sanitary
fixtures, showers, panes)
2.
Foam chemical action against dirt and bacteria,
3.
Rinsing with clean water, to remove foam residue from
the surfaces.
4.
Vacuuming of residual liquid
from floor.
The 10
advantages of Santoemma systems
1.
Better cleaning and sanitising result: chemical does not immediately fall onto
the floor, but stays for about 3 minutes on the surfaces where it has been
sprayed. This ensures both cleaning and sanitizing actions.
2.
The greatest hygienic safety for the
worker, who does not come
in contact with the surfaces and the objects to be cleaned and who does not
get wet by the bouncing water, because rinsing is done with low pressure.
3.
Reduced labour for the worker: manual work is reduced to a minimum
since the dirt is removed by the chemical action of the detergent and the
mechanical rinsing action.
4.
This
system, more comfortable and hygienic, gives a greater fulfilment to the worker.
5.
Saving of time: while the chemical acts on the surfaces
where it has already been sprayed, the worker is free to operate on other
surfaces. Therefore, even a big room can be completely cleaned quickly and
with no idle time.
6.
Detergent saving: the chemical is used without waste
because it does not immediately fall onto the floor.
7.
Reduced power consumption: the machines require little electrical
power and therefore they can be used in any place.
8.
Reduced water consumption: both systems rinsing at low pressure
require a minimal quantity of water. This avoids the flooding of rooms,
allows a longer working autonomy and offers the immediate availability of
the rooms that have been cleaned.
9.
Visual effect of foam: foam covers in white all the
surfaces where it is sprayed such as walls, sinks, fixtures. The operator
can therefore check that every corner has been covered, for a complete
action at every point.
10.
The
machines can be used also in places
with no drains because they can completely vacuum the water remaining
on the floor after rinsing.
Moreover, by
adding a special Santoemma device, it is possible to deliver a
sanitizing chemical in the form of dry fog@7micron. The dry fog is
delivered for a time sufficient to completely fill the rooms and then left
to act for a few minutes in order to exercise its sanitizing action. This
type of dry fog allows you to reach every point, without wetting the surfaces.
The machine can be left inside the room to be treated. Alternatively, you
can leave the machine out of the room, placing inside only the chemical
tank.
To watch the videos
of machines in action click here.
www.santoemma.com
|
